Sun Microsystems X2250 Manuel d'utilisateur Page 20
- Page / 134
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
1-8 Sun Fire X2250 Server Service Manual • April 2009
1.4.2 Powering On Main Power Mode
To power on main power for all server components:
1. Verify that the power cord has been connected and that standby power is on.
In standby power mode, the Power/OK LED on the front panel flashes. See
FIGURE 1-1.
2. Use a non-metallic stylus to press and release the recessed Power button on the
server front panel.
When main power is applied to the full server, the Power/OK LED next to the
Power button lights and remains lit.
1.4.3 Shutting Down Main Power Mode
To power off the server from main power mode, use one of the following two
methods:
■ Graceful shutdown: Use a non-metallic stylus to press and release the Power
button on the front panel. This causes Advanced Configuration and Power
Interface (ACPI) enabled operating systems to perform an orderly shutdown of
the operating system. Servers not running ACPI-enabled operating systems will
shut down to standby power mode immediately.
■ Emergency shutdown: Press and hold the Power button for four seconds to force
the main power off and enter standby power mode. When the main power is off,
the Power/OK LED on the front panel will begin flashing, indicating that the
server is in standby power mode.
Caution – To completely power off the server, you must disconnect the AC power cords
from the back panel of the server.
- Sun Fire 1
- X2250 Server 1
- Service Manual 1
- Contents 3
- Contents v 5
- Contents vii 7
- Index Index–1 8
- How This Book Is Organized 9
- Typographic Conventions 10
- Support and Training 11
- Product Updates 11
- Third-Party Web Sites 11
- Warranty 12
- Sun Welcomes Your Comments 12
- 1.1 Features 14
- 1.2.1 Preinstalled Software 15
- 1.3 Hardware System Overview 16
- 1.3.2 Internal Components 17
- Processor Configuration 19
- FIGURE 1-1 20
- 1.4.4 Clearing the CMOS 21
- Troubleshooting 23
- 2.1 Troubleshooting Overview 24
- Chapter 2 Troubleshooting 2-3 25
- Troubleshooting Procedures 26
- Chapter 2 Troubleshooting 2-5 27
- Problem Possible solution 28
- Chapter 2 Troubleshooting 2-7 29
- Performing Diagnostics 31
- Option Description 33
- Diagnostics Tests menu 34
- 3.3.1 Testing the Hard Disk 36
- 3.4 Immediate Burn-in Testing 37
- 3.5 Deferred Burn-in Testing 39
- ■ Select Yes and press Enter 42
- Solaris 10 Operating System 45
- 3.7 Show Results Summary 46
- 3.8 Print Results Report 48
- 3.9 About Pc-Check 48
- 3.10 Exit to DOS 48
- 4.1 Tools and Supplies Needed 49
- 4.2 Installation Precautions 50
- FIGURE 1-2) 51
- Removing the Server Cover 52
- 2 CPU 1 10 Dual blower module 53
- 5 DIMM slots (4) 13 I/O board 53
- 4.5.1 Replacing the I/O Board 55
- Installing the I/O Board 56
- 35W cards 57
- FIGURE 4-6 58
- FIGURE 4-7 58
- Removing a PCIe Card 59
- Installing the PCIe Card 60
- Removing a Hard Disk Drive 61
- Installing a Hard Disk Drive 62
- Carrier” on page 4-14 65
- Removing the ODD Filler Panel 67
- 4.5.6 Replacing the Air Duct 68
- To install the air duct: 69
- , aligning the baffle 69
- Installing the Air Duct 70
- Removing the Power Supply 71
- Installing the Power Supply 72
- Removing the Fan Module 73
- Installing the Fan Module 74
- 4.5.10.2 Removing a DIMM 77
- Bank 1 DIMM Slot Locations 78
- 4.5.10.3 Installing a DIMM 79
- Installing a DIMM 80
- FIGURE 4-30 for the 81
- Removing the System Battery 82
- Installing the System Battery 83
- FIGURE 4-32) 84
- Removing a Heatsink 85
- Removing the CPU 86
- Installing the CPU 87
- FIGURE 4-35 88
- 4.5.13 Installing a New CPU 89
- Installing the Heatsink 91
- 4.5.14 Replacing Cables 92
- 4.5.15 Motherboard 93
- Removing the Motherboard 94
- Installing the Motherboard 95
- 7. Replace the system cover 96
- System Specifications 99
- A.2 Power Specifications 100
- TABLE A-6 101
- B.2 Updating BIOS 104
- B.3 Updating SP Firmware 106
- B.3.2 ILOM Web Interface 107
- PXE Server 109
- # unzip syslinux-3.09.zip 110
- # cd /syslinux-3.09/memdisk 110
- Sun Fire X2250 Server 112
- Mainboard is Replaced 113
- With Optional Slide Rails 115
- Installation 116
- FIGURE C-2.) 117
- FIGURE C-3.) 118
- FIGURE C-4.) 119
- Setting the Rail Width 120
- Rail-width spacer 120
- Assemblies 121
- FIGURE C-6.) 122
- FIGURE C-6.) Continue 122
- Assembly 123
- CMA rail 124
- Left slide-rail 124
- Left slide rail 125
- Right slide rail 126
- CMA mounting 126
- CMA slide-rail 127
- Right slide 127
- CMA extension 128
- CMA arm connector 128
- (on left slide rail) 128
- Installing CMA Cable Hangers 129
- CMA cable hanger 129
Produits connexes et manuels pour Le serveur à l'état brut Sun Microsystems X2250
(63 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.115 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels