Sun-microsystems Ethernet MMF/UTP Adapter Manuel d'utilisateur télécharger pdf (Page 117)

Appendix C Installing the Sun PCI-Express Dual Gigabit Ethernet Device Driver on Linux Platforms 83

▼ To Set e1000 Parameters in a Linux

Environment

1. Remove the Sun PCI-Express Dual Gigabit Ethernet device driver, if it is already

loaded.

2. Load the Sun PCI-Express Dual Gigabit Ethernet device driver:

Or you can use the insmod command:

where VAL1 applies to the first e1000 interface and VAL2 to the next interface and so

on.

# rmmod e1000

# modprobe e1000 option=VAL1, VAL2, . . .

# insmod e1000 option=VAL1, VAL2, . . .

1 2 ... 112 113 114 115 116 117 118 119 120 121 122

PCI-Express Dual Gigabit 1
Ethernet MMF/UTP Adapter 1
Installation and User’s Guide 1
Contents 3
Index 87 7
FCC Class B Notice 9
FCC Class A Notice 9
BSMI Class A Notice 11
CCC Class A Notice 11
GOST-R Certiﬁcation Mark 12
Safety Agency Compliance 13
Statement 13
Battery Warning 14
System Unit Cover 14
Rack System Warning 14
Laser Compliance Notice 15
CD and DVD Devices 15
Mesures de sécurité 15
Symboles 16
Modification du matériel 16
Conformité SELV 16
Couvercle de l'unité 17
Vorschriften 18
Aufstellung von Sun-Geräten 19
SELV-Konformität 19
Anschluss des Netzkabels 19
Warnung bezüglich Batterien 19
Normativas de seguridad 20
Class 1 Laser Product 23
Luokan 1 Laserlaite 23
Klasse 1 Laser Apparat 23
Laser Klasse 1 23
Declaration of Conformity 25
Using UNIX Commands 30
Typographic Conventions 31
Shell Prompts 31
Related Documentation 32
Third-Party Web Sites 32
Sun Welcomes Your Comments 33
Sun PCI-Express Dual Gigabit 35
Ethernet Adapter Overview 35
Low-Profile Adapter 36
ExpressModule Adapter 39
ATNSW Attention Switch is a 41
Patches and Updates 43
Installing the Adapter 47
To Verify the Installation 48
Fiber pcs 51
Copper mif 51
Rebooting the System 52
Power Off 52
Hot-Plug 52
Configuring ipge and e1000 55
Driver Parameters 55
■ 100 Mbit/sec, half-duplex 56
■ 10 Mbit/sec, full-duplex 56
■ 10 Mbit/sec, half-duplex 56
■ Using the ndd utility 56
■ Using the ipge.conf file 56
■ Noninteractive 57
■ Interactive 57
TABLE 3-4 through TABLE 3-1) 58
% man prtconf 60
■ In this example: 61
Link Partner Parameters 62
To Discover Link Settings 64
Checking Configurations 64
# kstat ipge:0 65
Driver Operating Statistics 66
Parameter Description 67
Device Driver Parameters 68
Parameter Status Description 69
Operational Mode Parameters 70
Flow Control Parameters 71
Interpacket Gap Parameters 72
Interrupt Parameters 74
Jumbo Frames 74
Configuring e1000g Driver 77
Parameters 77
1 10 Mpbs half-duplex 81
2 10Mpbs full-duplex 81
3 100Mpbs half-duplex 81
4 100Mpbs full-duplex 81
Type the kstat command: 82
1500 but not 9000 90
Configuring VLANs 91
To Configure Static VLANs 94
Operating range Up 100 meters 98
Gigabit Ethernet UTP adapter 99
ExpressModule Performance 100
Specifications 100
ExpressModule Environmental 101
Requirements 101
Specification Measurement 102
Diagnostic Software 103
SunVTS Documentation 104
Using the SunVTS netlbtest 105
■ 10 Mbps PHY loopback 108
Linux Platforms 111
# depmod 112
# modprobe e1000 112
Low-Profile adapter 115
Environment 116
Keyword Description 118
Interfaces 120

Commentaires sur ces manuels

Pas de commentaire

Sun-microsystems Ethernet MMF/UTP Adapter Manuel d'utilisateur Page 117

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Sun-microsystems Ethernet MMF/UTP Adapter