Sun-microsystems SERVER 1290 Manuel d'utilisateur télécharger pdf (Page 32)

20 Netra 1290 Server Installation Guide • May 2006

Caution – The cabinet stabilizers (if applicable) must be extended or the cabinet

might topple when the lifting device is withdrawn.

7. With the lifting device still supporting the server, loosen the four captive screws

attaching the handles of the shipping cradle to the server.

8. Loosen the four captive screws that attach the handles to the shipping cradle.

9. Pull both shipping cradle handles away from the server.

This disconnects the shipping cradle from the server.

10. Lower the shipping cradle out of the way with the lifting device (

FIGURE 1-12).

Store the shipping cradle for future use.

FIGURE 1-12 Removing the Shipping Cradle

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 75 76

1290 Server Installation 1
Contents 3
Using UNIX Commands 9
Shell Prompts 10
Typographic Conventions 10
Related Documentation 11
Third-Party Web Sites 11
Sun Welcomes Your Comments 12
Unpacking the Server 13
Shipping kit 14
Opening the Shipping Carton 14
Carton protection pads 14
6. Remove the outer carton 15
Installing Slide Rails 16
FIGURE 1-3): 17
FIGURE 1-4) 18
Spring Clips and Cutouts 19
FIGURE 1-3) 20
FIGURE 1-6) 22
900 Cabinet 23
Rear bracket 24
Front bracket 24
Post Cabinet 25
Post Rack 26
FIGURE 1-8) 27
FIGURE 1-9) 28
(FIGURE 1-11) 30
Aligning the Rails 31
Inner rails 31
Outer rails 31
Removing the Shipping Cradle 32
Securing screw Securing screw 33
To Install the Lock Nuts 34
FIGURE 1-16) 35
Serial A Serial B 36
SSC1 SSC1 36
To Install the CMA–Lite 37
To Install the CMA–800 38
FIGURE 1-20 and FIGURE 1-21 39
Upper pivot bracket 40
Hinge pin 40
Upper CMA arm 40
Lower pivot bracket 41
Lower CMA arm 41
Slide rail 42
Left hand T-bracket 42
Right hand T-bracket 43
FIGURE 1-25) 44
Connecting Power Cables 45
Controller 46
FIGURE 1-26) 47
Connecting the I/O Assemblies 49
Setting Up 51
Setting Up the Hardware 52
On/Standby Switch 52
Powering On the Server 53
■ From the LOM port 54
■ By the On/Standby switch 54
# shutdown -i5 55
Do you want to continue? [no] 55
Setting Up the Server 56
Enter new password: 57
Enter new password again: 57
Operating System 58
Packages 59
To Install the LOM Drivers 60
To Install the LOM Utility 62
Chapter 2 Setting Up 51 63
Netra 1290 Server Connections 65
PCI+ IB_SSC Assemblies 66
SCSI Connector 67
Alarms Port 68
NET0/NET1 Ethernet Ports 69
1 TRD0_H 5 TRD2_L 70
2 TRD0_L 6 TRD1_L 70
3 TRD1_H 7 TRD3_H 70
4 TRD2_H 8 TRD3_L 70
■ Category 4 (STP-4) 71
RJ-45 Serial Connectors 72
RJ-45 Serial Connector Pinout 72
LOM Serial A 72
Serial B 72
TABLE A-9 lists the pin 73

Commentaires sur ces manuels

Pas de commentaire

Sun-microsystems SERVER 1290 Manuel d'utilisateur Page 32

Commentaires sur ces manuels

Produits connexes et manuels pour Ordinateurs Sun-microsystems SERVER 1290